All Types Of Imported Bearings

Ball Screw Assemblies

Rolled Precision Ground Ball Screw Assemblies

Spherical Bearings

Spherical Roller Bearings

All Types Of Linear Guideways Systems

Linear Motion Guideways

Needle Roller Bearings

Needle Roller Bearings

DC Sprag One Way Clutch

DC Sprag One Way Clutch

Taper Roller Bearings

Taper Roller Bearings

Hard Chrome Shafts For Linear Motion Bearings

Hard Chrome Shafts For Linear Motion Bearings

Linear Motion Slide Units - Linear Motion Bushes

Linear Motion Bearings Unit SC
Kluber Grease

Kluber Grease

Kluber NBU15 Grease

Kluber NBU15 Grease


Product List

Single-Row Deep Groove Ball Bearings

Pressed Steel Cages

Single-row deep groove ball bearings are the most common type of rolling bearings. Their use is very widespread.

In addition to open type bearings, these bearings often have steel shields or rubber seals installed on one or both sides and are prelubricated with grease. Also, snap rings are sometimes used on the periphery. As to cages, pressed steel ones are the most common.

For big deep groove ball bearings, machined brass cages are used.

Machined cages are also used for high speed applications.

Extra Small Ball Bearings and Miniature Ball Bearings

Miniature and instrument ball bearings can be divided into two basic types, deep groove and angular contact. The first (deep groove) can be further divided into the following five classes depending on their design details:

  • Standard type

  • Flanged outer ring

  • Extended inner ring

  • Expanded type in which one ring has a radial thickness that is larger than normal compared with the bearing width.

  • Thin section type in which both rings are extra thin in the radial direction. They can also be classified as: open, shielded, or sealed.

Maximum-Type Ball Bearings

Maximum-Type ball Bearings contain a larger number of balls than normal deep groove ball bearings because of filling slots in the inner and outer rings. Because of their filling slots, they are not suitable for applications with high axial loads. BL2 and BL3 types of bearings have boundary dimensions equal to those of single-row deep groove ball bearings of Series 62 and 63 respectively. Besides the open type, ZZ type shielded bearings are also available. When using these bearings, it is important for the filling slot in the outer ring to be outside of the loaded zone as much as possible. Their cages are pressed steel.

Magneto Bearings

The inner groove of magneto bearings is a little shallower than that of deep groove bearings. Since the outer ring has a shoulder on only one side, the outer ring may be removed. This is often advantageous for mounting. In general, two such bearings are used in duplex pairs. Magneto bearings are small bearings with a bore diameter of 4 to 20 mm and are mainly used for small magnetos, gyroscopes, instruments, etc. Pressed brass cages are generally used.


Product List

Single-Row Angular Contact Ball Bearings (Pressed Steel Cages & Machined Brass Cages)

Since these bearings have a contact angle, they can sustain significant axial loads in one direction together with radial loads. Because of their design, when a radial load is applied, an axial force component is produced; therefore, two opposed bearings or a combination of more than two must be used.

Since the rigidity of single-row angular contact ball bearings can be increased by preloading, they are often used in the main spindles of machine tools, for which high running accuracy is required.

Usually, the cages for angular contact ball bearings with a contact angle of 30° (Symbol A) or 40° (Symbol B) are in accordance with Table 1, but depending on the application, machined synthetic resin cages or molded polyamide resin cages are also used. The basic load ratings given in the bearing tables are based on the cage classification listed in Table 1.

Matched Angular Contact Ball Bearings

The types and features of matched angular Contact Ball bearings are shown in Table 2


Double-Row Angular Contact Ball Bearings

This is basically a back-to-back mounting of two single-row angular contact ball bearings, but their inner and outer rings are each integrated into one. Axial loads in both directions can be sustained, and the capacity to sustain moments is good. This type is used as fixed-end bearings.

Their cages are pressed steel.

Four-Point Contact Ball Bearings

The inner ring is split radially into two pieces. Their design allows one bearing to sustain significant axial loads in either direction.

The contact angle is 35°, so the axial load capacity is high. This type is suitable for carrying pure axial loads or combined loads where the axial loads are high.

The cages are made of machined brass.


Overview

Thrust ball bearings are classified into those with flat seats or aligning seats depending on the shape of the outer ring seat (housing washer). They can sustain axial loads but no radial loads. For Single-Direction Thrust Ball Bearings, pressed steel cages and machined brass cages are usually used The cages in Double- Direction Thrust Ball Bearings are the same as those in Single-Direction Thrust Ball Bearings of the same diameter series.

Features

  1. Available in two designs: single direction and double direction.

  2. To accommodate initial misalignments in an assembly both designs are available with spherical aligning seats or aligning seat washers.

  3. High quality steel-ultra clean steel to extend bearing life by up to 80%.

  4. Advanced Grease Technology — NSK lubricants that can extend grease life and performance.

  5. High Grade Balls — Quiet and smooth operation even at high speed.

  6. Optional seating rings take initial misalignment.


Bearing Size Chart

Bearing Chart